Electrical materials for high-pressure technology.

Suitable for mambrand pressure switch SW 27R+M No.: 913186203

Consisting of:Control box:Sheet steel housing RAL7035WxHxD: 300x300x150 mmIP66Power supply: 2 m cable with CEE plug 16 A, 400VAC, 50Hz, 3Ph/N/PE.Control voltage conditioning 24VAC, 20VA with 2 automatic circuit breakers.Motor output with 7.54kW power contactor.Timer relay for pulse extension. Adjustable from 0.05 seconds to 10 hours.Selector switch for continuous operation.The control cable is not included in the scope of delivery and must be ordered separately.Coin-operated machine:Powder-coated stainless steel housing.Incl. lock.

Used to switch high-pressure pumps on and off. high-pressure pumps. Contact 10 A - 380 V (AC1). Thread 3/8" female thread. Setting range 30-250 bar Max. 250 bar / 90 °C

Used to switch Pumpen, domestic waterworks etc.on and off. Contact 10 A - 380 V (AC1). Thread 3/8" IG. Setting range 2-32 bar Max. 10 bar / 90 °C

Used to switch Pumpen, domestic waterworks etc.on and off. Contact 10 A - 380 V (AC1). Thread 3/8" IG. Adjustment range 0.22-4 bar Max. 10 bar / 90 °C

Sheet steel housing RAL7035 WxHxD: 300x300x150 mm IP66 Power supply: 2 m cable with CEE plug 16 A, 400VAC, 50Hz, 3Ph/N/PE. Control voltage conditioning 24VAC, 20VA with 2 automatic circuit breakers. Motor output with 7.54kW power contactor. Timer relay for pulse extension.Toggle switch for switching to continuous operation.

Stainless steelContact 4 A - 24 V-250 VSeals EPDMCan be used as low water cut-outMax. 300 bar / 90°C

ST-5Float without hole.Vertical installation.Cable 1,200 mm.Contact 1 A - 250 V.0.3 l on. 0.17 l off.Max. 350 bar / 30 l/min / 80 °C.Inlet 3/8 "IGOutlet 3/8 "IG

High-Flow

Float with holeVertical installationCable 1,200 mmContact 1 A - 250 V3.4 l on. 2.9 l offMax. 350 bar / 30 l/min / 80°CInlet 3/8" female threadOutlet 3/8" female thread

Independent of position

New number after use *200505711

3/8" AG : 3/8" AG. Installation independent of position. Cable 1,200 mm. Contact 1 A - 250 V. 1.8 l on. 1.4 litres off. Max. 310 bar / 30 l/min / 80 °C

Used to switch high-pressure pumps on and off. high-pressure pumps. 1/4" MALE THREAD. Protection class IP65. Cable 1200 mm. 10 A. 250 V. Inrush current 20 A (NC contact) and 15 A (NO contact). Max. 350 bar / 45 l/min / 80 °C Switching points: at 1.5 l/min on. 0.8 l/min off This is a completely newly developed version of the flow monitor with a completely new operating principle. Instead of the usual highly sensitive REED-contacts with low switching capacity, a robust, industrial micro-switch is used here. This makes it possible to switch significantly higher electrical power switching with a longer service life. The electrical and water-hydraulic components of the flow monitor are completely separated from each other. The design of the flow monitor means that the electrical components can be independently of the hydraulic components in series production. components in series production. When the chassis and control box are joined together, the two parts of the flow parts of the flow monitor are joined together again. Due to the design, small switching points can be realised despite large maximum water volumes can be realised.

Used to switch high-pressure pumps on and off. high-pressure pumps. 1/4" MALE THREAD. Protection class IP65. Cable 1200 mm. 10 A. 250 V. Inrush current 20 A (normally closed contact) and 15 A (normally open contact). Max. 350 bar / 45 l/min / 80 °C Switching points: at 4.9 l/min on. 3.5 l/min off This is a completely newly developed version of the flow monitor with a completely new operating principle. Instead of the usual highly sensitive REED-contacts with low switching capacity, a robust, industrial micro-switch is used here. This makes it possible to switch significantly higher electrical power switching with a longer service life. The electrical and water-hydraulic components of the flow monitor are completely separated from each other. The design of the flow monitor means that the electrical components can be independently of the hydraulic components in series production. components in series production. When the chassis and control box are joined together, the two parts of the flow parts of the flow monitor are joined together again. Due to the design, small switching points can be realised despite large maximum water volumes can be realised.

Stainless steel with clip Max. 400 bar / 150°CAdapter for connecting hoses with 11 mm plug nipple.

Incl. 5 sets of pressing jaws:12 - 14 mm14 - 16 mm16 - 19 mm19 - 23 mm23 - 27 mmKey features of the P16 HP:Press head accessible from both sidesCompact designTwo-stage hand pumpPress size adjustment is steplessPressing dimension control via signal lampCarrying handleDrawer recessed in the housing for storing the pressing jawsThe P16 HP hose press is a sophisticated, high-quality machinespecially developed for the assembly and repair of hose lines on site.on site.The press is easy to learn to use thanks to its practical design.Technical data:Length of base jaws: 64 mmMax. Opening diameter: Min. press diameter + 20 mmCrimping capacity: 2-wire hose up to DN 25Crimping range: 10 - 45 mmMax. Pressing force: 720 kNCapacity per stroke: 3.62 cm3 / 0.90 cm3Pressure: 14 bar / 630 barWeight (without oil): 20 kgDispatch by forwarding agent.